If you suspect there is a problem with your hardware, use the diagnostic flowchart in “Diagnosing the Problem” in Chapter 4 to help isolate the problem before calling your local SGI service provider.
The following topics are covered in this chapter:
Before calling your local SGI provider, have the following information ready. You can record the information in the space provided in Table 5-1.
system serial number (see “Locating Your Workstation's Serial Number” in Chapter 1)
hardware configuration information including hardware upgrades, and IRIX software version (choose Toolchest > System Manager)
description of the problem
Use this space to record the information you need for your support call.
Table 5-1. Information Needed for Support Call
System Serial Number |
|
Model Number |
|
IRIX Version |
|
Description of Problem |
|
Remove the faulty part if instructed by your service provider to do so. See these sections:
To replace
memory modules, see “Removing Memory Modules” in Chapter 2.
PCI boards, see “Removing a PCI Board: R5000 Workstation” in Chapter 2 or “Removing a PCI Board: R10000 Workstation” in Chapter 2.
digital display adapter such as the Presenter 1280 adapter, see “Removing a Digital Display Adapter Board” in Chapter 2.
a second optional hard drive (R5000 workstations), see “Removing the Second Internal Hard Disk Drive” in Chapter 3.
system module, see “Replacing the System Module”.
CPU module, see “Replacing the R5000 CPU Module” or “Replacing the R10000 CPU Module”.“Replacing the R10000 CPU Module”
system drive, see “Replacing the System Drive”.
audio visual module, see “Replacing the Audio-Visual Module”.
power supply, see “Replacing the Power Supply”.
CD-ROM drive, see “ Replacing the CD-ROM Drive”.
PCB on the PCI tray, see “Replacing the Chassis”.
If you are instructed by your service provider to replace the system module, follow these steps.
Before replacing your system module, you must remove the memory modules, PCI tray, CPU module, and digital display adapter board (if one is installed) from your existing module and reinstall them on the replacement module you received.
Note: It's important that you remove the PCI tray, because the printed circuit board beneath it contains a host chip with important information such as the workstation's serial number. |
Follow these steps:
Remove the power cable, and remove the system module from the chassis. See “Removing the System Module” in Chapter 2 and “Reinstalling the System Module” in Chapter 2.
Remove all of the DIMM modules from the system module you are returning and reinstall them on the replacement system module. See “Removing Memory Modules” in Chapter 2 and “Installing Memory Modules” in Chapter 2.
Remove the PCI tray from the system module you are returning, and reinstall it on the replacement system module. If a PCI board is installed in the tray, do not remove it from the tray.
R5000 workstations, see “Removing a PCI Board: R5000 Workstation” in Chapter 2 and “Installing a PCI Board: R5000 Workstation” in Chapter 2.
R10000 workstations, see “Removing the PCI Tray: R10000 Workstation” in Chapter 2 and “Installing a PCI Board: R10000 Workstation” in Chapter 2.
Remove the CPU module from the system module you are returning, and reinstall it on the replacement system module.
R5000 workstations, see “Replacing the R5000 CPU Module”.
R10000 workstations, see “Replacing the R10000 CPU Module”.
Remove the digital display adapter board, if one is installed, and reinstall it on the replacement system module. See “Removing a Digital Display Adapter Board” in Chapter 2 and “Installing a Digital Display Adapter Board” in Chapter 2.
Ship the stripped-down system module back to Silicon Graphics in the container that held the new system module.
If you are instructed by your service provider to replace the R5000 CPU module, follow these steps.
If you haven't already done so, turn off the workstation, remove the power cable, and remove the system module from the chassis. See “Removing the System Module” in Chapter 2.
Release the PCI tray by pushing up the lever on the side (Figure 5-1). The tray pops up.
Push down slightly on the rear of the PCI tray and remove it from the system module (Figure 5-2). Do not remove the PCI board (if one is installed) from the tray.
Before touching any of the components, ground yourself to a metal part of the chassis. Attach the wrist strap to your wrist and to the metal flange (Figure 5-3).
Locate the R5000 CPU module (Figure 5-4). Use a Phillips screwdriver to remove the two screws from the locations shown.
Note: The illustrations show the current CPU. Future CPUs may look a little different, but the installation steps are the same. |
Grasp the CPU module on both sides and gently rock it out (Figure 5-5). Do not exaggerate the rocking motion, or you will bend the pins.
Install the replacement R5000 CPU module (Figure 5-6).
Align the connector beneath the module with the connector on the system board. Make sure it's positioned correctly before pressing down.
Press down gently on the CPU module until it is securely seated. You hear a click as it connects.
Insert and tighten the two Phillips screws in the locations shown (Figure 5-6).
Remove the wrist strap.
Reinstall the PCI tray in the system module (Figure 5-7).
Push the lever on the side of the tray to return it to its starting position.
Engage the hinge on the PCI tray in the slot.
Lower the tray, pushing toward the back of the system module as you do this.
Align the gold-colored PCI edge connector with the slot on the system board.
Push the tray down firmly until it is completely seated. Check that the lever returns to its starting position (Figure 5-8).
Note: If the PCI tray is not completely seated, the system module will not slide back into the chassis. |
Reinstall the system module, and reconnect the cables. See “Reinstalling the System Module” in Chapter 2.
Ship the old CPU module to Silicon Graphics in the container that held the replacement CPU module.
If you are upgrading your R5000 CPU module with a newer CPU, the instructions for installing the processor module are different depending on which version of the operating system you are using.
Note: The RM7000 CPU upgrade requires IRIX 6.5.9 or higher. If your shipment includes an RM7000 CPU upgrade, you must install the IRIX 6.5.9 operating system prior to installing the CPU upgrade. |
Follow the installation instructions provided here in the order in which they are given:
Install the operating system software, if needed
Install the software patches
Install the hardware
Before upgrading your CPU, perform the following step:
Determine your workstation's IRIX operating system version. From the Toolchest, choose Desktop > UNIX Shell. At the prompt, enter:
uname -R |
If you see 6.3 O2 R10000 or 6.3 O2, check your shipment (see “Checking Your Shipment”), go to “Installing the Upgrade on IRIX 6.3 Systems”, and follow the instructions for your workstation's specific IRIX 6.3.
If you see 6.5.x O2 and you are installing an R5000 class CPU upgrade, check your shipment (see “Checking Your Shipment”) and then go to “Installing the Upgrade on IRIX 6.5 Systems”.
If you see 6.5.x O2 (where x is less than 9) and you are installing the RM7000 class CPU upgrade, you must upgrade your workstation to the IRIX 6.5.9 operating system before installing the hardware. Confirm your shipment (see “Checking Your Shipment”) and then go to “Installing the Upgrade on IRIX 6.5 Systems”.
The following items are included in a CPU upgrade shipment:
IRIX 6.3 for O2 Including R10000 CD
IRIX 6.3 Recommended/Required Patches 6/99 CD
IRIX 6.5.x[1] Overlay CDs
Wrist strap
Reversible screwdriver
R5000 class (RM5271) or RM7000 class CPU processor module
Upgrade label
Follow the upgrade instructions in this section if your system is running IRIX 6.3.
To upgrade your CPU, verify that you are running correct version of IRIX 6.3 and if not, upgrade to the required version. Then install the IRIX 6.3 Recommended/Required Patches 6/99 CD and install the processor module upgrade.
Procedures for locating and installing relevant documentation begin in “Viewing This Guide From the IRIS InSight Library” in Chapter 1.
Install the software before installing the hardware.
For the O2 R5000 class CPU upgrade, you need the version of the IRIX operating system software called “IRIX 6.3 for O2 Including R10000.” Follow the steps below to make sure your system is running the correct version before installing the patches and beginning the hardware upgrade.
Check your workstation's IRIX version. In a shell window, enter:
uname -R
If you see 6.3 O2 R10000, you have the correct IRIX version. Go to “Installing the IRIX 6.3 Recommended/Required Patches 6/99 CD”.
If you see 6.3 O2, you must upgrade your workstation to the correct operating system before installing the patches and the hardware. The IRIX 6.3 for O2 Including R10000 CD is included in this shipment. Read the Caution below, and then go to step 2. Otherwise go to “Installing the IRIX 6.3 Recommended/Required Patches 6/99 CD”.
Caution: Do not install the patch CD that contains the recommended patches now. You do this later, after the IRIX and Applications CDs are installed and you have rebooted the workstation. If you install the patches without rebooting, the flash PROM environment variables may become corrupt. |
Install IRIX 6.3 for O2 Including R10000
Read any letters or instructions that came with the CD. The CD booklet explains how to read the release notes.
When IRIX 6.3 for O2 Including R10000 has been installed, you must reboot the system before installing the patches CD. From the toolchest, choose Restart System. Log in as usual when you see the Login screen.
You are ready to install the patches.
Note: Now that the system is running the correct version of IRIX, if you ever need to boot from a CD (the miniroot), you must use the “IRIX 6.3 Recommended/Required Patches CD”, not an operating system CD. The new hardware (CPU) is not compatible with the original IRIX 6.3 operating system CD. |
Caution: If you just installed “IRIX 6.3 for O2 Including R10000” and have not rebooted your system, do so before installing the “6.3 Recommended/Required Patches 6/99” CD. |
Insert the “6.3 Recommended/Required Patches 6/99” CD in the CD-ROM drive and double-click the CD-ROM drive icon on the desktop. If you have a root password set, you are prompted to enter it.
Read the Installation Startup message that displays and click Dismiss.
Choose /CDROM/dist/ in the Software Manager window, and click Open.
Read the Installation Startup script and follow the instructions.
In the Software Manager window, follow the instructions to install the patches. Click Start to begin installation. When you are asked in the Open Additional Distribution window if you want to install additional software, click Done.
Follow the installation instructions that are displayed in Software Manager. When the installation is complete, from the File menu choose Exit.
From the Toolchest, choose System > Restart System.
You may be removing a processor module that has one of two form factors, L-shaped or rectangular shaped. The processor module you receive with this upgrade is L-shaped.
Note: Attach the O2 upgrade label near the system label on the bottom of the workstation. |
To install the processor module upgrade in your workstation, follow these steps.
If you haven't already done so, turn off the workstation, remove the power cable, and remove the system module from the chassis. See “Removing the System Module” in Chapter 2.
Release the PCI tray by pushing up the lever on the side (Figure 5-9). The tray pops up.
Push down slightly on the rear of the PCI tray and remove it from the system module (Figure 5-10). Do not remove the PCI board (if one is installed) from the tray.
Before touching any of the components, ground yourself to a metal part of the chassis. Attach the wrist strap to your wrist and to the metal flange (Figure 5-11).
Locate the CPU module (Figure 5-12). Use a Phillips screwdriver to remove the two screws from the locations shown. Grasp the CPU module on both sides and gently rock it out (Figure 5-12). Do not exaggerate the rocking motion, or you will bend the pins.
Install the upgrade CPU module (Figure 5-14).
Align the connector beneath the module with the connector on the system board. Make sure it's positioned correctly before pressing down.
Press down gently on the CPU module until it is securely seated. You hear a click as it connects.
Insert and tighten the two Phillips screws in the locations shown (Figure 5-14).
Remove the wrist strap.
Reinstall the PCI tray in the system module (Figure 5-15).
Push the lever on the side of the tray to return it to its starting position.
Engage the hinge on the PCI tray in the slot.
Lower the tray, pushing toward the back of the system module as you do this.
Align the gold-colored PCI edge connector with the slot on the system board.
Push the tray down firmly until it is completely seated. Check that the lever returns to its starting position (Figure 5-16).
Note: If the PCI tray is not completely seated, the system module will not slide back into the chassis. |
Reinstall the system module, and reconnect the cables. See “Reinstalling the System Module” in Chapter 2.
Ship the old CPU module to Silicon Graphics in the container that held the replacement CPU module.
If your workstation does not boot after installing the processor module, read the processor module installation instructions carefully to make sure the new processor module is correctly seated. Be sure you installed the software before installing the hardware.
Check that the system is running the correct version of IRIX. See “Verifying and Installing the Operating System”.
If necessary, remove the new hardware, reinstall the old hardware, install the operating system software, remove the old hardware, and install the new hardware.
Follow the upgrade instructions in this section if your system is running IRIX 6.5.
To upgrade to the R5000 class CPU, install the IRIX 6.5.x Overlay software and install the processor module.
To upgrade to the RM7000 class CPU, install the IRIX 6.5.9 (or higher) Overlay software and install the processor module.
Install the software before installing the hardware.
For the R5000 class processor module upgrade, you need the IRIX 6.5.x Overlay software that came with this shipment. You must have IRIX 6.5 base software installed.
For the RM7000 class processor module upgrade, you need the IRIX 6.5.9 Overlay software that came with this shipment. You must have IRIX 6.5 base software installed.
Note: IRIX 6.5 base operating system software does not ship with the processor module upgrade. Contact your local sales representative to order the base operating system. Install the base operating system software, then the 6.5.x Overlay CDs before installing the processor module. |
To check your workstation's IRIX version, from the Toolchest, choose Desktop > UNIX Shell.
At the prompt, enter:
uname -aR |
Use the Installation Instructions booklet that comes with your IRIX 6.5.x Overlay CDs for installing the operating system software.
Install the software before installing the hardware.
For instructions on installing the processor module upgrade, see, “Installing the Processor Module”.
Note: Attach the O2 upgrade label near the system label on the bottom of the workstation. |
If your workstation does not boot after installing the processor module, read the instructions carefully to make sure the new processor module is correctly seated. Be sure you installed the software before installing the hardware.
Check that the system is running IRIX 6.5. To check your workstation's IRIX version, from the Toolchest, choose Desktop > Unix Shell. At the prompt, enter:
uname -aR |
If necessary, remove the new hardware, reinstall the old hardware, install the software, remove the old hardware, and install the new hardware.
If you are instructed by your service provider to replace the R10000 CPU module, follow these steps.
To remove the R10000 CPU module, you must first remove the plastic face plate of the system module and the PCI tray.
If you haven't already done so, turn off the workstation, remove the power cable, and remove the system module from the chassis. See “Removing the System Module” in Chapter 2.
Remove the plastic face plate from the system module:
Use a Phillips screwdriver to remove five screws on the rear and two screws on the underside, in the locations shown (Figure 5-17). Keep the two screws from the underside separate. When reinstalling the faceplate you must use the same screws.
Caution: On the underside, remove only two screws. Do not remove the third screw that attaches the lever to the face plate. |
Remove the faceplateby grasping it where the plastic comes to a “V” and pulling it outward(Figure 5-18).
There is a filler panel covering the I/O port which falls away as you remove the face plate.
Release the PCI tray from the system module as follows. If a PCI board is installed in the tray, do not remove it from the tray.However you need to disconnect any cables attached to the PCI board.
Insert a screwdriver in the small opening shown in Figure 5-19. Use a twisting motion to release the PCI connector from the slot on the system module. Then use an up and down motion to release the PCI tray.
Pull the PCI tray straight up to remove it and set it aside.
Before touching any of the components, ground yourself to a metal part of the chassis. Attach the wrist strap as follows: (Figure 5-20)
Locate the R10000 CPU module. It is protected by a metal heat sink (Figure 5-21). Do not remove the heat sink.
Use a Phillips screwdriver to remove four screws from the locations shown (Figure 5-21).
Caution: Do not remove the four hex screws. Do not remove the two screws that secure the fan. |
Grasp the CPU module on both sides and gently rock it out (Figure 5-22). Do not exaggerate the rocking motion, or you will bend the pins. Set the CPU module aside.
Install the replacement R10000 CPU module (Figure 5-23).
Align the screw holes on the CPU module with the screw holes on the CPU support. Make sure it is positioned correctly before pressing down.
Press down gently on the CPU module until it is securely seated. You hear a click as it connects.
Insert and tighten the four Phillips screws in the locations shown.
Remove the wrist strap.
Replace the PCI tray in the system module as follows:
Lower the PCI tray, engaging it on the metal rear panel of the system module (Figure 5-24).
Insert the PCI connector beneath the tray into the slot on the system module.
Once the connector is aligned, push down firmly until it is completely seated.
Note: If the PCI tray is not completely seated, the system module will not slide back into the chassis. |
Replace the faceplate by sliding it onto the system module, while at the same time lifting slightly at the “V” to snap it in place (Figure 5-25).
When properly seated, the underside of the faceplate is flush to the module and the screwholes are aligned.
Align the screwholes on the faceplate with the screwholes on the system module. Use a Phillips screwdriver to insert and tighten two screws on the underside in the locations shown (Figure 5-26).
Replace the filler panel over the I/O opening on the inside of the module. It snaps into place. If it doesn't seem to fit, turn it 180 degrees and try again.
Use a Phillips screwdriver to insert and tighten five screws in the locations shown (Figure 5-27).
Ship the original CPU module to Silicon Graphics in the container that held the replacement CPU module.
If you are upgrading your R1000 CPU module, this section describes the installation of an R12000 or R12000A CPU and the necessary software to support the upgrade.
Caution: If you're uprading your O2 with an R12000A module, it's important that you complete the replacement of the CPU support prior to installing the module or your CPU will be damaged during its installation. |
Included in this shipment are the following items:
6.5.x[2] Overlay CD
Wrist strap
Reversible screwdriver
R12000 or R12000A CPU processor module
CPU support (P/N 050-0347-002) for use with the O2 R12000A only
Upgrade label
Make sure you install the software before installing the hardware. You must have IRIX 6.5 base software installed to be able to install the Overlay IRIX 6.5.x software. For this upgrade, use the IRIX Overlay CD that shipped with this R12000 CPU hardware.
Note: IRIX 6.5 base software does not ship with the processor upgrade. Contact your local sales representative to order the base IRIX 6.5. |
To check your workstation's IRIX version, from the Toolchest > Desktop, open a UNIX shell.
At the prompt, enter
uname -aR
To install the software, follow the instructions in the software installation booklet that came with your CDs.
For instructions on installing the R12000 processor, follow the instructions for replacing the R10000 CPU module in “Replacing the R10000 CPU Module”. When you have completed the CPU installation, see“Attaching the Upgrade Label”.
To replace an R10000 or R12000 CPU module with an R12000A CPU, you must first remove the plastic face plate of the system module and the PCI tray.
If you haven't already done so, turn off the workstation, remove the power cable, and remove the system module from the chassis.
Remove the plastic face plate from the system module:
Use a Phillips screwdriver to remove five screws on the rear and two screws on the underside, in the locations shown (Figure 5-28). Keep the two screws from the underside separate. When reinstalling the faceplate you must use the same screws.
Caution: On the underside, remove only two screws. Do not remove the third screw that attaches the lever to the face plate. |
Remove the faceplate by grasping it where the plastic comes to a “V” and pulling it outward (Figure 5-29).
There is a filler panel covering the I/O port which falls away as you remove the face plate.
Release the PCI tray from the system module as follows. If a PCI board is installed in the tray, do not remove it from the tray. However you need to disconnect any cables attached to the PCI board.
Insert a screwdriver in the small opening shown in Figure 5-30. Use a twisting motion to release the PCI connector from the slot on the system module. Then use an up and down motion to release the PCI tray.
Pull the PCI tray straight up to remove it and set it aside.
Before touching any of the components, ground yourself to a metal part of the chassis. Attach the wrist strap as follows: (Figure 5-31)
Locate the R10000 or R12000 CPU module. It is protected by a metal heat sink (Figure 5-32). Do not remove the heat sink.
Use a Phillips screwdriver to remove four screws from the locations shown in Figure 5-21.
Caution: Do not remove the four hex screws. Do not remove the two screws that secure the fan. |
Grasp the CPU module on both sides and gently rock it out (Figure 5-33). Do not exaggerate the rocking motion, or you will bend the pins. Set the CPU module aside.
Use the Phillips screwdriver to remove the top two screws securing the clear plastic CPU support to the system module (Figure 5-34).
Turn over the system module and use the Phillips screwdriver to remove the third screw securing the CPU support in place (Figure 5-35).
Note: If the system module does not have a hole in the sheet metal to access this screw, call your nearest SGI Customer Support Call center and report the nature of the problem. |
Remove the CPU support and set it aside.
Insert the new CPU support in the system module as shown in Figure 5-36. The new CPU support can be distinguished from its predecessor by its gray color or by the part number 050-0347-002 embellished on it.
Reinsert the two screws from the top to secure the CPU support into place.
Reinsert the bottom screw to secure the CPU support into place as shown in Figure 5-37.
Install the replacement R12000A CPU module as shown in Figure 5-38.
Align the screw holes on the CPU module with the screw holes on the CPU support. Make sure it is positioned correctly before pressing down.
Press down gently on the CPU module until it is securely seated.
Insert and tighten the four Phillips screws in the locations shown.
Remove the wrist strap.
Replace the PCI tray in the system module as follows:
Lower the PCI tray, engaging it on the metal rear panel of the system module (Figure 5-39).
Insert the PCI connector beneath the tray into the slot on the system module.
Once the connector is aligned, push down firmly until it is completely seated.
Note: If the PCI tray is not completely seated, the system module will not slide back into the chassis. |
Replace the faceplate by sliding it onto the system module, while at the same time lifting slightly at the “V” to snap it in place (Figure 5-40).
When properly seated, the underside of the faceplate is flush to the module and the screw holes are aligned.
Align the screw holes on the faceplate with the screw holes on the system module. Use a Phillips screwdriver to insert and tighten two screws on the underside in the locations shown (Figure 5-41).
Replace the filler panel over the I/O opening on the inside of the module. It snaps into place. If it doesn't seem to fit, turn it 180 degrees and try again.
Use a Phillips screwdriver to insert and tighten five screws in the locations shown in Figure 5-42.
See the section, “Replacing the System Module”.
Ship the original CPU module to Silicon Graphics in the container that held the replacement CPU module.
Attach the O2 upgrade label near the system label on the bottom of the workstation.
If your workstation does not boot after installing the CPU, reread the CPU installation instructions. Check to make sure the new CPU is correctly seated. If you mistakenly installed the new R12000 CPU before installing the software, follow these steps:
Remove the new CPU module.
Reinstall the old CPU module.
Install the software.
Remove the old CPU module.
Install the new CPU module.
If you need further help to troubleshoot the installation, see your owner's guide. If necessary, contact your local authorized service provider.
If you are instructed by your service provider to replace the system drive, follow these steps.
Before replacing the system drive, you must turn off the workstation, remove the power cable and other exterior cables, and attach the wrist strap. Follow these steps:
Turn off the workstation.
Remove the power cable from the rear.
Note: The illustrations show an R5000 workstation. Replacing the system drive is the same on an R10000 workstation. |
Pull down the lever on the left side of the system drive module to release it (Figure 5-45).
Pull the system drive module out of the chassis (Figure 5-46).
Slide the replacement system drive module into the system drive bay (Figure 5-47).
Push the lever up to lock the module in place (Figure 5-48).
Reconnect the power cable and turn on the workstation.
If you are instructed by your service provider to replace the audio-visual module, follow these steps.
Turn off the workstation.
Remove the power cable and any cables that are connected to the rear or side panel of the audio-visual module (Figure 5-51).
Note: The illustrations show an R5000 workstation. Replacing the audio-visual module is the same on an R10000 workstation. |
Pull down the lever on the left side of the audio-visual module to release it (Figure 5-52).
Slide the audio-visual module out of the chassis (Figure 5-53).
Slide the replacement audio-visual module into the chassis (Figure 5-54).
Push the lever up to lock the module in place (Figure 5-55).
Reconnect the power cable any audio-visual cables that you removed earlier (Figure 5-56).
Turn on the workstation (Figure 5-57).
If you are instructed by your service provider to replace the power supply, follow these steps.
Turn off the workstation (Figure 5-58).
Remove the power cable from the rear (Figure 5-59).
Note: The illustrations show an R5000 workstation. Replacing the power supply is the same on an R10000 workstation. |
To release the bezel that covers the power supply, press the latch at the top of the bezel (Figure 5-60). It swings out toward you. Remove it from the chassis.
Slide the lever to the right to release the power supply (Figure 5-61).
Grasp the pull ring and slide the power supply out of the chassis (Figure 5-62). Put it aside.
Slide the new power supply in to the chassis, pushing it until it stops (Figure 5-63).
Push the lever to the left until it clicks (Figure 5-64).
Replace the bezel over the power supply. Place the tabs at the bottom of the bezel in the slots on the chassis and snap it up into place (Figure 5-65).
Reconnect the power cable (Figure 5-66) and turn on the workstation.
If you are instructed by your service provider to replace the CD-ROM drive, follow these steps.
Replacing the CD-ROM drive involves several steps. You must first remove the exterior covers before you can reach the drive. Follow these steps:
If the CD eject button does not work, insert a straightened paper clip in the tiny hole beneath the eject button to release the CD-ROM tray (Figure 5-67). (The CD eject button may not work if the CD-ROM has failed.)
Remove the CD-ROM drive face plate as follows (Figure 5-68).
Hold the face plate between the thumb and forefinger of one hand while bracing the tray with the other hand.
Push the face plate (but not the tray) upward with the thumb until it snaps away from the tray.
Push the tray gently back into the drive until it is just inside the bezel. Do not push it all the way. It will be easier for you later to extract the tray to reinstall the face plate.
Turn off the workstation and remove the power cable from the rear.
To release the bezel that covers the power supply, press the latch at the top of the bezel. It swings out toward you (Figure 5-69). Remove it from the chassis.
Note: The illustrations show an R5000 workstation. Replacing the CD-ROM drive is the same on an R10000 workstation. |
Remove the top cover of the CD-ROM drive as follows (Figure 5-70).
Use a Phillips screwdriver to remove the two screws that secure the outer cover (Figure 5-71).
Remove the outer cover by grasping the plastic cross-piece and lifting up the cover (Figure 5-72).
Use a Phillips screwdriver to remove the two screws that secure the CD-ROM drive (Figure 5-73).
oTilt the CD-ROM drive upward and unhinge it from the chassis. (Figure 5-74).
Caution: The CD-ROM drive has sharp metal edges. Be cautious when you handle it. |
Disconnect the SCSI and power cables as follows (Figure 5-75).
Place the faulty CD-ROM drive aside.
Pick up the replacement CD-ROM drive.
Reconnect the SCSI cable and the four-wire power cable to the replacement CD-ROM drive (Figure 5-76).
Press each connector in firmly.
Tuck the excess length of the SCSI cable with the terminator into the cavity between the connector and the sheet metal.
Install the replacement CD-ROM drive by sliding the two hinges on the drive's bezel into the slots on the chassis and lowering the drive until it is fully seated (Figure 5-77). Make sure that you do not pinch the SCSI and power cables as you lower the drive.
Insert and tighten the two screws that secure the CD-ROM drive (Figure 5-78).
Replace the outer cover by aligning the three screw holes on the cover with the screw holes in the CD-ROM tray and lowering the cover until it is fully seated (Figure 5-79).
Insert and tighten the two screws that secure the outer cover (Figure 5-80).
Replace the top cover (Figure 5-81).
Replace the plastic bezel over the power supply by inserting the hinges into the slots beneath the power supply and pivoting the bezel up until it snaps into place (Figure 5-82).
Replace the CD-ROM drive face plate as follows (Figure 5-83).
Pull the tray out gently.
Align the guides on the sides of the face plate with the grooves on the sides of the CD-ROM tray.
Push the face plate down while supporting the tray, until the release tabs lock. Do not place too much downward pressure on the tray.
Push the tray back into the drive.
Reconnect the power cable and turn on the workstation.
If you are instructed by your service provider to replace the chassis, follow these steps.
Replacing the chassis consists of several steps. You must remove all of the removable modules and reinstall them on the new chassis.
Caution: The chassis has sharp metal edges. Be cautious when you handle it. |
Turn off the workstation, remove the power cable, and remove the system module from the chassis. See “Removing the System Module” in Chapter 2. Reinstall the system module on the replacement chassis. See “Reinstalling the System Module” in Chapter 2.
Remove the system disk drive and reinstall it on the replacement chassis. See “Replacing the System Drive”.
R5000 workstations: If an optional internal hard drive is installed, remove it and reinstall it on the replacement chassis. See “Removing the Second Internal Hard Disk Drive” in Chapter 3.
Remove the audio-visual module and reinstall it on the replacement chassis. See “Replacing the Audio-Visual Module”.
Remove the power supply and reinstall it on the replacement chassis. See “Replacing the Power Supply”.
Remove the CD-ROM drive and reinstall it on the replacement chassis. See “ Replacing the CD-ROM Drive”.
Ship the stripped-down chassis shown in Figure 5-85 to Silicon Graphics.
Reconnect the power cable and turn on the workstation.
The system serial number is stored electronically (nvram) on the printed circuit board on the PCI tray. If nvram is corrupted, you may be instructed by your service provider to replace the PCI tray that contains the printed circuit board. Follow these steps:
Turn off the workstation, remove the power cable, and remove the system module from the chassis. See “Removing the System Module” in Chapter 2.
Note: You can find illustrations for all the following steps in “Installing a PCI Board: R5000 Workstation” in Chapter 2, “Removing the PCI Tray: R5000 Workstation” in Chapter 2, “Installing a PCI Board: R10000 Workstation” in Chapter 2, and “Replacing the R10000 CPU Module”. |
Remove the PCI tray from the system module.
If a PCI board is installed in the tray, remove it. If not, remove the filler panel and screw.
Reinstall the PCI board into the new PCI tray. If no PCI board was installed, reinstall the filler panel and screw.
Reinstall the PCI tray into the system module.
Reinstall the system module into the chassis. See “Reinstalling the System Module” in Chapter 2.
Ship the PCI tray with the faulty PCB to Silicon Graphics in the container that contained the new PCI tray.
[1] Overlay software is labeled “IRIX 6.5.x, “x” referring to the current numbered version of the software, for example 6.5.9. Base software is referred to as IRIX 6.5.
[2] “The Overlay version of IRIX 6.5 software that you received with this shipment. Overlay software is labeled “IRIX 6.5.x, “x” referring to the current numbered version of the software, for example 6.5.3. Base software is referred to as IRIX 6.5.